Other Products

Other Products Supplied by AlBurhan Group

MEDIUM PRESURE FAN

ITEM	SPECIFICATION	QTY.
1	2900 RPM 11KW TYPE MVS 400/660 125 M/H 230 MM WS	38

LOW PRESSURE FAN

ITEM	SPECIFICATION	QTY.
1	P=1.2 T= 20 V=170M/MIN PT 2= 150 N=1500 7.5KW	10
2	ANR 46220 A 1450 RPM, 15KW TYPE HTM 45.18 LI Q=220M/MIN PSTAT = 220MIMWS	15

AIR LOCK

ITEM	SPECIFICATION	QTY.
1	AIR LOCK TYPE B 225 IN. DIA. 17CM OUT. DIA. 17CM HIG. 28CM DIA. OF THE SHAFT 2.5 CM	360
2	IN. DIA. 12.5 CM OUT. DIA. 12.5 CM HIG. 31CM DIA.OF THE SHAFT 3 CM	360
3	TYPE ST 25/11 DIA = 183 MM	90
4	TYPE LE 151
5	PP 250 WITHOUT DRIVE	220

TECHNICAL SPECIFICATIONS FOR THE DRY STONERS

CLEANIING CAPACITY TON/H	QTY.
2.5	4
4.5	13
6.5	23
8.5	2
12.5	1

Each unit should be complete with air system, cyclon, air loch …etc. i.e. the unit is completely self contained.

Operation voltage is 380V, 3 ph, 50 hz.

Protection of all motors and electrical parts should be I P 54 or better.

The units should be suitable for continuous use at an ambient temp of 50 °C.

Technical specifications fro tempering units

The quantities and capacity of the tempering units required are as shown bellow.

Each unit should consist of the following basic parts:

A.	A sensor (S) which senses the initial moisture content of the grain flow in the range of 6-18% and also senses the moisture content of the dampened grain in the range of 18% or more.

B.	A controller coupled to the sensor with a device for setting the required final moisture content in the dampened grain. According to the mentioned setting the controller determines the amount of water to be added based on the initial moisture content reading of the sensor (S).

C.	A flow meter or continuous weigher which determines the amount of grain dampened this weigher should have the possibility of being connected to a computer which registers the amount of grain dampened.

D.	An intensive dampener complete with screw conveyors, paddles, water piping, water manual and electro-magnetic valves, water pump(s), air compressor(s) cables for interconnections, control boards, motors, switches …etc. i.e. it should be completely self sufficient. The intensive dampener is completely controlled by the above mentioned controller in item (B)

Item	Qty. required	Capacity of unit in tons/hour
1	24	6
2	40	8
3	13	9
4	10	11
5	10	13
6	18	15

The sensor, controller, weigher and all other relevant parts should be temperature compensated.

Operating voltage is 380V, 3PH, 50HZ.

Protection of all electrical parts should be IP54 or better.

A priced spare parts list for two years operation is to be included in the offer.

The supply should include a set of operating, maintenance and spare parts catalogues with each unit plus two extra sets for our technical department.

Drawing, catalogues, photographs and any other clarification means should accompany the offer.

10.

The offer should include supervision of errection and starting up of some of the units for a period of one month by your technicians and at the same time training a group of our engineers and technicians on the errection and starting of other units and on repairing faults which may occur in operation. All costs relating to your technicians are to be born by you. The starting of the above mentioned month of supervision shall be agreed upon latter between our two companies.

11.

The offer should include the training of two of our engineers at your factory for a suitable period on the repair of faults which may occur in electronic parts.

Rotary Magnets

1.	The magnets should be of the rotary self-cleaning type suitable for fitting in flour mills.
2.	The unit should be complete with the rotary self-cleaning magnet and all other accessories.
3.	Protection of all electrical parts should IP54 or better.
4.	Operating voltage is to be 380V, 50HZ, 3PH.
5.	The units should be suitable for use at an ambient temp. of 50°C.
6.	The offer should include a priced spare parts list for two years operation.
7.	The strength of magnet should be stated in the offer and should be sufficient to remove a high percentage of iron pieces from the stream of grain.
8.	Operation and spare parts catalogues should be supplied with each magnet.

No. of magnet units	Rate of flow of grain for which it is required tons/hour
23	4.5
65	8.5
17	12.5
3	17

Technical specification for flour bag filling stations

No. of filling months	Quantity required	Max height of station
4	6	5M
3	59	5M
1	34	4M

Filling capacity 100-150 bags per month per hour, weight of each bag 50kg.
Method of vibration is to be used in the bag filling process.
Each filling ststion is to be complete with all accessories including counters, safety devices..etc.

Each filling station should include:
- an electronic weigher of a recent generation with the possibility of connecting it to a computer;
- a belt conveyor for moving the filled bags from the station which has a sewing head for sewing the filled bags

Operating voltage is to be 380V, 50HZ.
Protection of all motors and electrical parts should be IP 54 or better.

Technical specifications for belt-conveyors

Qty. 90 Units,
Hand movable belt conveyors of a type similar to the one shown in the sketch and of the following specifications:

1.	The conveyor consists two parts; the belt of each part is driven by an independent motor.
2.	Each part can be moved vertically and independently from the other part by a hydraulic system, the range of vertical movement should be from near zero level at the tip of the belt to about three metres above horizontal level for the long part and about one metre for the short part.
3.	It should be possible to reverse the direction of movement of the belt through a simple push button or a switch.
4.	Each belt should be fitted with an independent tensioning device.
5.	The hydraulic system should be self sufficient and includes a tank of a suitable size and a pump; a hand operated pump is acceptable.
6.	The types on which conveyor moves should be of the solid rubber type and fitted with hand brake.
7.	The conveyors should be of strong construction suitable for heavy duty use and at the same time as light as possible and easily movable.
8.	The belt should be of the non slip anti static multiply type, a small sample of the belt should be submitted with the offer.
9.	The rollers should be galvanized and should not need periodic oiling or greasing.
10.	Protection of all electrical parts should be IP54 or better.
11	Operating voltage to be 380V, 50 Hz, 3ph.
12.	The width of the belt is to be 80cm; other dimensions are to be as shown in the sketch.
13.	Each conveyor should be fitted with a 25cm. long 4 core flexible cable with thick outer insulation and with the each core well marked.
14.	All metal parts of the conveyor should be well connected to the earth core of the cable.
15.	The conveyor should be fitted with electrical control for each belt for start/stop and reserve functions.
16.	The conveyor should be able transport twenty bags of flour of 50kg. per minute continuously at least.
17.	The conveyor should be suitable for operating at ambient temp. of 50c.
18.	The offer should include a priced spare parts list for two years heavy duty operation.
19.	The offer should include the training of four of our engineers on the repair and maintenance of the conveyor, the training is to take place at your factory for a period of fifteen days, all costs are to be borne by you.
20.	The supply should include a set of operating, maintenance and spare parts catalogues with each conveyor, plus two extra sets for our technical dept.
21.	The offer should include photos, drawing …etc, shoeing details of the offered conveyors, a list of previous similar supplies is welcomed.
22.	If the conveyors arrive in Iraq dismantle then re-building should be done under your supervision and at you expense, and by your experts.
23.	The conveyors should be guaranteed for a period of nine month from the date of arrival in Iraq.

Rolls for flour mills

Item	Dia.length		Shaft L (MM)	Size Dia (MM)	Qty. (PCS)
Item	MM	MM	Shaft L (MM)	Size Dia (MM)	Qty. (PCS)
1	250	1500	450	100	32
2	250	1250	375	95	32
3	250	1000	375	95	1500
4	250	800	350	90	144
5	250	630	315	85	132
6	250	600	210	85	116
7	250	500	400	85	164
8	190	500	215	60	368
9	190	400	215	60	204
10	10 Inch	60 Inch	20 Inch	110 MM	20
11	10 Inch	40 Inch	20 Inch	110 Inch	20
					Total 2732

Motors

Item	P=KW	RPM	Qty.
1	3	700	13
2	3	1000	13
3	5.5	1000	38
4	7.5	1000	50
5	7.5	1500	31
6	11	1000	50
7	11	1500	50
8	15	1000	50
9	15	1500	13
10	18.5	1000	25
11	18.5	1500	15
12	18.5	3000	25
13	22	1500	13
14	22	3000	5
15	30	3000	10
16	45	3000	20
17	55	3000	5
18	75	3000	5
19	11	750	13
20	22	1000	25
21	30	1000	13
22	45	1000	5
23	45	1500	8
24	60	1500	5
25	11	3000	6

		Total	506

Gear boxes

Item	P=KW	RPM	Qty.
1	1.1	50 Flange	53
2	1.1	50 Foot	38
3	7.5	50 Flange	5
4	7.5	50 Foot	13
5	1.5	50 Flange	30
6	1.5	80 Foot	30
7	1.5	100 Foot	13
8	2.2	50 Foot	50
9	3	50 Foot	30
10	3	80 Foot	30
11	5.5	80 Foot	25
12	5.5	50 Foot	30
13	2.2	80 Foot	38
14	7.5	80 Foot	13
15	5.5	100 Foot	18
16	5.5	120 Foot	13
17	5.5	20 Foot	3
18	7.5	120Foot	8
19	3	120 Foot	11
20	3	100Foot	30
21	2.2	120 Foot	33
22	2.2	100 Foot	31
23	1.5	120 Foot	18
24	1.5	50 Foot	43
25	1.5	20 Foot	3
26	1.1	120 Foot	19
27	1.1	100 Foot	13
28	1.1	80 Foot	14
29	1.1	20 Foot	3
30	0.75	100 Foot	18
31	0.75	50 Foot	25
32	0.55	50 Foot	10
33	11	120 Foot	1
34	11	80 Foot	4
35	5.5	50 Flange	18
36	5.5	100 Flange	15
37	3	100 Flange	13
38	3	50 Flange	8
39	7.5	100 Flange	1
40	7.5	20 Flange	4
41	1.1	100 Flange	28
42	1.1	20 Flange	8
43	1.5	100 Flange	30
44	2.2	100 Flange	13
45	2.2	50 Flange	38

			Total 892

Lab. Equipment for flour mills (Grain processing)

	Code	Description	Qty.
1		Lab dough mixer cap. 1-2 kg, two seed with moving cover	4
2	01-01-00878	Modern mixograph equipment	3
3	01-01-00879	Rapid moisture tester for wheat	120
4	01-01-00880	Wheat moisture tester	120
5	01-01-00881	Lab. Flour sifter	120
6		Potentiometric strippin analyzer	1
7		Atomic spectroscopy	1
8		G. C. mass spector	1
9	01-01-0076	H.P.L.C. model P. 42661-00	1
10		Proten measurement equipment kjeted ahism automatic G.C.IR	1
11		Soxhiet equip for lipids measurement	3
12		Gluten washer type mil=500	10
13		Fiber measuring equip	3
14		Graper PC6 A series 4	10
15		Circular polarimeter type Mild 106	15
16		Photometer type ML1 465	2
17		Zeleny sediniution equipment	3
18		Fuchmixome drum mixer	1
19		Spare parts for rapidmoisture Contact thermometer (90-170°C)	20
20		Balance analyst relais	10
21		Heating element	20
22	01-01-0089	Frosted glass vitre depolic	20
23	01-01-00899	Precent scale	20
24	01-01-00889	Aliminume plates for rapid moister tester	20
25	01-01-0099	Standard steel disc for rapid moister tester (spare parts for alveograph) thermo regulator (20-97°C) with armature.	20
26		Heater 500W 220V with bottom heater	10
27		Felt tip pen holder	50
28		Felt tip pen	50
29		Special electric top watch	10
30		Special mirror with holder and steel arm	5
31		Damping oil pin spnner	30 ton
32		Special manual stop watch	10
33		Special mini ceramic cup using for measuring the ash	300